Lift the scanner assembly and then with the top cover until it is firmly in place.

Hold the middle handle of the imaging drum and pull it along the track to remove it with the toner cartridge.

Remove the new imaging drum and toner cartridge from the protective bag.

The old imaging drum and used toner cartridge should be properly disposed off for recycling.

Hold the middle handle of the imaging drum align it with the tracks inside the printer and push down until the drum clicks in the place.

Close the top cover and the lower the scanner assembly.

For more information, visit HP Printers website or for HP Printer Repair, please contact us.

41.2 PRINTER ERROR: Indicates that a beam detect laser scanner error has occurred on the previous page. The page will reprint and continue.
Solution:
1. Reset the Printer by restarting it
2. Reconnect connector J1001 on the laser driver PCA and connector J205 on the controller board.
3. if this does not help, replace the controller board

41.3 UNEXPECTED PAPER SIZE LOAD TRAY 1: This happens when the printer tray detects a different paper size than the normal. Verify the correct size media (width and length)
are loaded in tray. You might have to replace the tray 1 pick-up assembly as a last resort.

50.1 FUSER ERROR CYCLE POWER: Indicates that a low temperature error has occurred in the fuser. Time to replace fuser kit if resetting does not help

Contact us for all types of HP Laserjet Repair and Maintenace service.

When the printer control panel is stuck on the HP logo white screen on the initialization screen, follow these steps to clear the control panel screen.

• Make sure the printer is connected to a computer with a USB cable.
• The printer driver must be installed on the computer.
• Download the latest firmware.
• go to www.hp.com/support, select your country, then select your language
• click “get software and drivers”
• Enter into your printers model number and click find my product
• Scroll down and click to expand the firmware section
• click download on the latest firmware for your printer
• click next to begin downloading the firmware
• click view downloads folder
• follow this step to update the firmware to the latest version
• navigate to the downloaded firmware and double-click the firmware icon, the firmware extracts and then opens
• click update
• Select your printer and click update do not disconnect the USB cable or the power cord while the update runs
• Click close of the update successful screen to complete the firmware update

Your firmware is updated and Printer is good to run. For HP Printer Repair, contact our service team.

1. To maintain high-quality printing and performance, get your printer regularly serviced from a Printer Repair company who can thoroughly clean the printer and the paperhandling
   accessories
2. Before cleaning, always turn off the power top avoid any shock or injury
3. While cleaning the printer, never touch the transfer roller. Skin oils on the roller can reduce print quality.
4. Use a lint free damp cloth to clean outside cover, pickup rollers, feed, separation rollers and Fuser.
5. Only use dry lint free cloth to clean Separation pad, Registration roller, Transfer roller and other general inside parts
6. Do not touch the transfer roller with the damp cloth or with your fingers.
7. If there is spilled toner, clean it using a cloth dampened with cold water.

Contact us for  HP Printer Repair Service in your area. We have years of experience and skills to handle even the toughest of repair issues.

Light print or faded on paper

This issue can be due to several factors including the following:

• Your print cartridge is nearing end of life and needs to be replaced.
• You are using a poor quality compatible toner
• The paper quality is not up to the mark such as the paper is too moist or too rough.
• If the whole page is light, the print density adjustment is too light or EconoMode might be turned on. Adjust the
  print density, and disable EconoMode in the printer Properties.

Toner spread or small toner particles on the Paper

• The paper quality is not good or too rough.
• Printer needs cleaning

Dark Grey background on Paper

• Make sure that tray 1 is in place.
• Decrease the print density setting through the embedded Web server. This decreases the amount of background shading.
• Change the media to a lighter basis weight.
• Check the device environment. Very dry (low humidity) conditions can increase the amount of background shading.
• Try Installing a new HP print cartridge.

Dropouts, jamming, or curl

• The paper has been stored incorrectly
• The paper has variability from one side to the other.
• The paper has ragged edges.

For complete service for HP Laserjet Printers, please contact us.

This article will show you how to assign  a static IP address to your HP printer using the embedded Web server or EWS.

Before you begin you need to printer network configuration page to get your printers IP address. putting the network configuration page varies by printer so we will not provide those instructions here your computer go to the desktop if you are at the start screen click the bottom left corner of your screen. Open the web browser of your choice. using the network configuration page you printer located the IP address for your printer. type the IP address into the browser’s address bar and then press enter on your Keyboard. If  receive a warning message about the website security certificate continue to the website doing so will not harm your computer. when the embedded Web server opens this confirms the printer is on the same network as the computer. In the EWS click the network tab. Click networking, then click the network address or the IP. Click manual IP and then click suggest a manual IP address. After the manual IP address populates, click manual DNS server. Using the network configuration page you printed, locate the Project locate the DNS server addresses for your printer.  Type the DNS server addresses for your printer into the manual preferred DNS server field and the manual alternate DNS server field. Click apply.The static IP address is now assigned printers ready for regular use.

For complete HP Printer Repair Service in Toronto, contact us at Printer Repair Hub Canada.

• Error 13 Paper Jam
• Error 13.20 4200/4300/ 4250/4350
• 13.20/13.14 or 13.X on power up for all other printers
• 50.x error
• 50 Service on LaserJet series II, III, IID, IIID, IIP, IIIP,4P, 4L, 5P, 6P, 4, 4+, 5
• 50.5 Error 4200/4300/4250 & 4350 only
• Image Defects: Ghosting, Repetitive Print, Offset Printing
• Grinding Noise

If you get any of the above errors on your Printers, please get in touch with our HP Printer Repair Department.

Fast and Affordable Printer Repair

We are the first choice for small and large companies located in the GTA. We also carry a large inventory of printer parts some of which are hard to find. We have a team of highly experienced printer repair technicians in Toronto and we cater to printer repair calls on the same day. We deliver comprehensive on site printer repairs, support services and printer maintenance solutions throughout Ontario. Our goal is to exceed your expectations in the areas of printer quality, cost and service. Call to arrange a quick appointment at (416) 623-9693 or e-mail us at support@printerrepairhub.com. We will dispatch our printer repair technician at the shortest possible time. We service and repair various types of printers including Color printers, Monochrome Laser, Multifunction printers, Fax Machines, Multi-Function Copiers, Label Printers and Plotter printers. Our Printer Repair Service Technicians carry all the necessary parts, tools including printer vaccum to service clean your printers. They have all the technical competence to repair your equipment on the first visit.

On-Site Printer Repair Toronto Area

Some of the common printer problems include:

• Printer does not print
• Paper jam or paper out
• The LP spooler do start
• whites Lines on print pages
• printer does not start
• network printer does not print
• power failure
• ink or toner cartridges empty
• Random Characters printing issues
• Printer Features Not Working
• Error messages on the printer
• Printer printing strange characters
• printer spooler crash
• Printing is too slow
• Prints are lighter than expected
• prints contain white spots or horizontal lines
• Colors are missing
• printer leaves heavy ink
• Bad Cartridges

We can handle your printer problems in shortest possible time. We also offer a great range of compatible printer parts and laser printer maintenance products for brands such as HP, Canon, Epson, Brother, Xerox and Lexmark. Our competitive rates and trained technicians can come to you the same day or as per your convenient time.

Contact us

[si-contact-form form=’1′]

We provide the following services:

• Onsite HP Printer Repair Service in entire Brampton. We service all HP laserjets and Designjet machines including HP parts
• Same day and next day service available.
• Service and maintenance contracts available.

HP Printer Repair Brampton

We stock all major parts for HP printers including Printer Maintenance kits, Fuser assembly, Rollers, Separation Pads, Fuser gears, Transfer rollers, Face Down Rollers and Trays.

Some of the HP printer Models we service Includes:

Complete Printer Cleaning:
We not only services your machine but thoroughly Vaccum clean for best and lasting results. Most of the Printer issues are related to an accumulation of dust and dirt and therefore we take special care of your printers so that they last longer with good results.

Plotter Printer Repair

Some of popular plotter printers we service includes the following:

HP DesignJet 510 – large-format printer
HP DesignJet T790ps ePrinter – large-format printer
HP DesignJet 111 – large-format printer
HP Color LaserJet Enterprise CP5525n
HP DesignJet T790 ePrinter
HP DesignJet Z3200ps
HP DesignJet Z6100ps
HP DesignJet T610
HP DesignJet Z6200
HP DesignJet Z3200
HP DesignJet Z5200ps
HP DesignJet Z6100
HP DesignJet T1200ps